Dial in Your Personal PA Mix with Signal Processing

Browse By

Check 1, 2 

In this article we’ll cover signal processing for personal PAs. Hopefully after reading this article, you’ll be ready to dial in your personal PA mix to perfection with Signal Processing.


The equalizer (EQ) is probably the most important processor in the live sound arsenal. EQ can help you adjust the main speakers to match the room acoustics, eliminate feedback in the mains and the monitors, and sculpt the sound of individual channels.

Whether you’re using a powered analog mixer, passive analog mixer, or a digital mixer, you’ll find individual EQ controls of some sort on each individual channel. In more basic mixers, these may consist only of knobs that boost and cut the low, mid, and high bands. Higher-quality mixers often add sweepable frequency knobs to the midrange or even to all three bands. These give you more precise control over which frequencies you’re adjusting. The channel EQs in digital mixers provide more control and more extensive features than you typically find on analog models.

Dial in Your personal PA Mix with Signal Processing
DBX 231s Dual 31 Band Graphic Equalizer

The graphic EQ is another important equalizer type for a PA system, especially if you have monitors. Graphic EQs allow you to boost or cutting a range of fixed frequencies. The more frequency sliders on a graphic EQ, the more precision it offers.

Some mixers offer graphic EQs built in, or you can add them in the form of outboard rackmount units, such as the dBX-231S Dual 31 Band Graphic Equalizer which get connected between the outputs of your mixer (main or monitor) and your powered speakers or amplifiers. Digital mixers provide a variety of EQ types including graphic EQs. For example, the Soundcraft Ui12 features a digitally controlled 31-band graphic EQ as well as a host of other effects.

Tour sound engineers use the graphic EQ for “ringing out” the speakers, which involves boosting gain on the various frequencies of the graphic EQ until feedback is heard, and then cutting them. When properly done, it allows you to get more gain from the speakers before feedback. It’s an especially important task to do with stage monitors, which, because of their proximity to the microphones, are highly prone to feedback

Feedback Suppressors

Feedback suppressors are commonly found in digital mixers, as part of speaker management processors (see section below), or as standalone outboard units. Most feature digital algorithms that detect and attenuate feedback frequencies before the feedback becomes audible.

While they shouldn’t be thought of as a substitute for properly equalizing your system, they function as a secondary line of defense against feedback, and can make operating a PA system a lot easier.

Compressors and Limiters

Dynamics processors, such as compressors and limiters, control the dynamic range of your music, which is the difference between the loudest and softest portions. They can be used for applications like smoothing out a lead vocal on an individual mixer channel or preventing loud volume spikes in the main speakers.

Dial in Your personal PA Mix with Signal Processing

Compressors work by lowering the level of any signal that goes above a user selectable threshold. The amount of compression is controlled by the ratio control, which is expressed in decibels, such as 2:1, 3:1, 4:1 and so forth. A 2:1 ratio will reduce the signal that exceeds the threshold to half its original level, a 3:1 ratio to a third of its original level, and a 10:1 to a tenth of its original level. The higher the ratio, the more you’re squashing the dynamic range, which is the difference between the loudest and softest signal.

While you’re likely to find compressors for each channel in a digital mixer, most analog mixers, except expensive professional models, don’t include individual channel compressors.

A limiter is an extreme form of compressor, which has a very high ratio, and is designed to squash down peaks. Limiters are usually found on the master channels of digital mixers and some analog mixers. They keep loud peaks from getting through to the speakers, which is important both for speaker protection and for preserving the audience’s listening experience.

Dial in Your Personal PA Mix with Signal Processing

Speaker Management Processors

A speaker management processor is typically an outboard processor that offers a range of functions for a PA system. These often include equalization, feedback suppression, dynamics processing and crossovers (the latter is useful if your system includes a subwoofer).

There are  models available, such as the ultra-affordable dbx DriveRack PA2 Processor. It can be connected to your speakers, and lets you easily control the volume, mute the entire system, adjust the Anti-Feedback circuit, and add compression and EQ. It also has a Sub Synth feature that enhances low end in the speaker system by synthesizing frequencies an octave below the area of 100 Hz. This feature can make your speakers seem to reproduce more bass.

Ambience Effects

Reverb and delay are two important effects to have in your PA and are the icing on the cake allowing you to add space to vocals and instruments. You could use an outboard reverb unit or multi-effects unit, connected to your mixer. You probably won’t need to do that, however, as most contemporary analog PA mixers (and powered mixers) have built-in effects, offering at least reverb in different room sizes to suit. Some will also give you a range of creative effects including chorus, flanging and more. For example, the Soundcraft Signature Series consoles are equipped with a built-in Lexicon digital effects processor with studio-grade reverb, chorus, modulation and other effects and dbx limiters on the input channels

You’re will most likely get the widest selection of varied effects from a digital mixer and they will also provide you with the advantage of letting you save custom settings.

Soundcraft Signature Series

It’s a Wrap

Because mixers often provide some or all the signal processing you’ll need for your PA, it makes sense to wait until you’ve settled on a mixer to decide whether you need additional processors. Depending on your system, you can probably get by with the channel EQs and reverb from your mixer as your only processors.

If you have monitors in your system, you’ll probably find you need a graphic EQ, as well. If you can swing it, speaker management processors with built in limiters and anti-feedback circuitry will make your life a lot easier.

Thank you! Your subscription has been confirmed. You'll hear from us soon.
Subscribe to our Newsletter
Stay up to date with all our best articles and exclusive giveaways via our newsletter.